24 Août 2012

Peterson BBS-1 MIDI SysEx format

Category: HardwareRaphaël Doursenaud @ 18 h 57 min

I just received my brand new metronome and began tinkering with it.

The device revolves around an ARM Cortex-M3 platform from ST Electronics (the STM32F103) and a wireless chip from Microchip (the MRF24J40MA).

The USB mode is fortunately class compliant and is seen as a standard MIDI device.

The proprietary BodyBeatSync software emits and receives SysEx data to the device’s MIDI ports.

3 startup modes are available:

  • Documented
    • Normal starts the metronome
    • Firmware Update starts in mode waiting for a firmware update (press TEMPO while powering up or plugging USB)
  • Undocumented
    • LCD test displays the full custom LCD (press PRESET/MIDI while powering up)

The ultimate goal is to make an application that will run on most FOSS OSes to load MIDI tempo maps without using the proprietary sync software (which runs fine in Wine BTW).

Here’s the data I’ve been able to collect so far :

Normal mode init
-> F0 00 40 70 01 02 00 20 00 00 00 00 F7
<- F0 00 40 70 01 03 00 21 F7
-> F0 00 40 70 01 02 00 22 00 00 00 00 F7
<- F0 00 40 70 01 03 00 23 00 F7
-> F0 00 40 70 01 02 00 15 00 00 00 00 F7
<- F0 00 40 70 01 03 00 16 00 00 00 00 01 00 03 00 02 F7
-> F0 00 40 70 01 02 00 13 00 00 00 00 F7
<- F0 00 40 70 01 03 00 14 00 00 00 00 01 00 00 00 00 F7
-> F0 00 40 70 01 02 00 17 00 00 00 00 F7
<- F0 00 40 70 01 02 00 18 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
-> F0 00 40 70 01 02 00 04 7F 7F 00 00 F7
<- F0 00 40 70 01 02 23 19 00 00 00 00 00 42 42 53 01 03 3C 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
<- F0 00 40 70 01 02 23 19 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
<- F0 00 40 70 01 02 23 19 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
<- F0 00 40 70 01 02 23 19 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
<- F0 00 40 70 01 02 23 19 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
<- F0 00 40 70 01 02 23 19 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7
<- F0 00 40 70 01 02 19 7F 7F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F7

Firmware update mode init
-> F0 00 40 70 01 02 00 20 00 00 00 00 F7
<- F0 00 40 70 01 03 00 21 F7
-> F0 00 40 70 01 02 00 22 00 00 00 00 F7
-> F0 00 40 70 01 02 00 15 00 00 00 00 F7
-> F0 00 40 70 01 02 00 13 00 00 00 00 F7
<- F0 00 40 70 01 03 00 23 01 F7
<- F0 00 40 70 01 03 00 16 00 00 00 00 01 00 00 00 00 F7
<- F0 00 40 70 01 03 00 14 00 00 00 00 01 00 00 00 00 F7

Firmware update cmd 0
-> F0 00 40 70 01 02 00 03 00 00 00 00 00 00 00 2D 0B 21 0F 71 54 F7
Firmware tx
-> F0 00 40 70 01 02 23 01 00 [ADDR 00-23] 00 00 [DATA] F7
[...]
-> F0 00 40 70 01 02 14 01 7F 7F 00 00 [CHECKSUM?] F7
Firmware ack
<- F0 00 40 70 01 03 00 02 7F 7F 00 00 F7
Firmware update cmd 1
-> F0 00 40 70 01 02 00 03 00 00 00 00 00 [N] 00 2D 0A 7B 78 5A 28 F7
[loop until finished]

Laisser une réponse